Results of laboratory researches on determination of suitability of clay raw materials of the Zvezdinsky field for production of a facing ceramic brick are stated by way of plastic formation. It is established that for receiving faultless products it is necessary to reduce air shrinkage and sensitivity to drying of a structure. Additives – sandy loam of the Dubovsky field and a fuel-bearing additive are for this purpose used. For increase of frost resistance of a ceramic crock entered the mineral modifying additive into a structure – waste of production of mineral fertilizers. Its introduction in number of 5% allowed to increase frost resistance to 50 cycles without deterioration of appearance of the burned samples. In addition, on the burned samples made of all structures there was a whitish raid. For the purpose of receiving a monophonic surface the svezhesformovannykh of samples applied special water solution for elimination of a white raid on two sides. These actions reached receiving the samples corresponding to facing products.

Keywords: clay raw materials, facing brick, plastic formation, mineral modifying additive, air shrinkage, sensitivity to drying, frost resistance

Article is dedicated to increasing the effectiveness of the regional integration policy of the Southern Federal University in southern Russia. The concept of creation and development of educational research and innovation complex - Department of regional integration on the basis of the higher school of the university.

Keywords: South Russia, South Federal District, Southern Federal University, technology department

The article investigates the formation and development of the network of the Cossack cadet corps in Russia. Cadet education is seen as a unique and effective system for producing high-quality secondary education and upbringing of the younger generation.

Keywords: Cadet Corps, military education, the Cossacks, traditions and education

The assessment of economy of the electric power and reduction of emission of greenhouse gases across the Nizhny Novgorod Region due to introduction of the equipment having marking in household sector, the budgetary sector and on other objects of energy consumption (buildings) on prospect till 2030 is carried out

Keywords: marking of power efficiency, engineering equipment, electrical household appliances

In article the basic principles and factors having impact on successful functioning of regional infrastructure are considered the analysis of priority investment projects of the Chechen Republic is carried out, practical recommendations about improvement of infrastructure service of real sector of economy are made.

Keywords: production infrastructure, target programs, priority directions, investment projects, social and economic problems, transport complex

in modern conditions become widespread trenchless methods for the construction of pipelines. The positive features of their use include increased speed pipeline installation, reducing the volume of excavation, etc. Existing regulatory documents limit the bending of the pipe at low temperatures need to be tested in terms of their applicability to new grades of polyethylene. The aim of this study was to determine the minimum permissible bending radius of the track, the passage of which in the conditions of negative temperatures polyethylene pipes PE80 would maintain its strength characteristics. By using a mathematical model dependency of the elastic modulus and yield point are calculated from the temperature stresses in the walls of pipes of different diameters in bending under different temperatures. In order to establish empirical relationships voltage on the pipe diameter and the radius of its bend procedure is carried out function approximation method of least squares. Presented obtained graphic dependences. Using the values ​​of the yield strength of the material at different temperatures were calculated bending radius of all dimensions. If the production of the track plow trenchless pipe-layer will be considered given the conditions, you will be provided with the necessary conditions for installation.

Keywords: plastic pipe, trenchless pipe layer, the stress-strain state, trenchless techniques, pipelining

The article describes and analyzes how to determine the thermal residual stresses. The conclusion, based on the analysis, showed the necessity of the calculation method for determining the residual stresses, which is based on a mathematical model of the formation of residual stresses and deformations occurring during heat treatment. The results of calculation of stresses and comparison with experimental data are given.

Keywords: residual thermal stresses, finite element method, heat treatment, low-hard details

The phenomenon of buckling under the creep of concrete arches was investigated. Solution of the problem carried out by means of the finite element method. To analyze the stability we used Newton-Raphson method. It has been established that there is a long-term critical load, beyond which the growth of the deflection has not fading character. As the equation of the relationship between the creep deformation and strains we used viscoelastoplastic hereditary model of aging concrete. To determine the creep strain we used a linear approximation with respect to time. It was found that the long critical load for considered arch was in 1.44 times lower than the instant critical load.

Keywords: reinforced concrete arch, stability, creep, geometric nonlinearity, finite element method, Newton-Raphson method

In this paper we propose mathematical model of salient-pole synchronous generator of mini-CHP. The model is based on a full Park-Gorev differential equation. The saturation of the machine is taken by using the method of partial magnetic characteristics. This method allows most accurate evaluation of the change of parameters of an equivalent circuit of the generator in the absence of information about the magnetic properties of the machine. The model is Implemented in Simulink. Application of the model is possible when calculating the steady-state and transients in distribution electrical net wich contains salient pole synchronous generators.

Keywords: salient-pole synchronous generator, mathematical model, Park-Gorev differential equation, magnetic characteristics, transients

The article highlights main problems of agricultural development of KBR and basic measures of their solution. The necessity of state support of agriculture as a natural condition for the functioning of this industry is also justified.

Keywords: agriculture, government support, endogenous and exogenous factors, innovation development, technology

Infringements of variability of an intimate rhythm in a combination to attributes of electric instability of a myocardium are one of factors of diabetic heart.

Keywords: arterial hypertensia, diabetic heart, variability of an intimate rhythm.

The results received at research of influence electron beam treatment processings on tool life of a tungstenless hard alloy metal on the basis of TiC with a binding material an alloy Ni-Cr-Al and percentage of the components "basis-binding" 50 – 50% about are presented in the conditions of metal cutting. Influence electron beam treatment of a blanket of samples of the cutting tool insert on technological components of force of cutting when turning cut metal is experimentally revealed.

Keywords: Surface coating, hard alloy metal, structural and phase modification, electron beam treatment, tool life, metal cutting, wear, technological components cutting force

An analysis of science researches and production experience have shown that there is a need in the method of determining the number of vehicles and special technics for transport units in the pipeline industry. Decided to consider the system of transport and technological service of pipeline's repair processes as queuing system. A simulation method as a tool for determining the need of vehicles was chosen. The correlation between factors of primary production and the number of vehicles and special technics was determined.

Keywords: oil pipeline, car, special equipment, vehicle, demand for vehicles, modeling, quantity of technics, standardization, technical maintenance of cars

Problems for the design of low-voltage CMOS op-amps are considered: low voltage headroom for signal swings, increase the swing of input and output common-mode signal and sustainability when the feedback. Ways to implement input and output stages of low-voltage CMOS op-amps for technology 0.13 um at 1 V are investigated. The ways of frequency compensation are investigated. According to the results of modeling the best gain and the largest swing of input and output signal have continuous in time common-mode feedback circuit (CMFB) and the proposed two-stage current mirrors op-amp. These op-amps can be applied at a supply voltage ~ 1 V.

Keywords: low-voltage CMOS operational amplifiers (op-amps), the input and output swing, miller-effect frequency compensation

Developed a rapid method for evaluation of the homogeneity of mixtures hardly separated granular materials, the analysis of which is the use of known methods is impossible or time-consuming. The method is based on the separation of mixture components by color using computer processing of pictures of her samples. To implement the developed computer program that can calculate the values of the coefficient of heterogeneity of the mixture, as well as other dispersion parameters.

Keywords: express method, the concentration of the mixture, component, granular material, image, distribution, shade of gray, the coefficient of heterogeneity